The Foundation of Plumbing Skills for Bathtub Installation
Request A QuoteThe content listed below relating to Installing A Bathtub is especially motivating. Don't bypass it.
Setting up a tub isn't exactly brain surgery, however it does need strong plumbing, carpentry, as well as often, tiling abilities. Changing an old bathtub with a brand-new one is likewise a moderately hard job. If the old bathtub is easily available, the task can relocate rapidly; if you have to open up a wall to eliminate the old bathtub and also position the new tub, the task is much harder. In either instance, the task is within a home handyman's abilities, although you will certainly require a helper to vacate the old tub and also embeded in the new one. Ensure you have certified yourself for the work and fit trying it. Instead of hiring a specialist to take over a halfway-completed task, it is better to consider utilizing one prior to you start. Opportunities are you may need a specialist plumber to make tube connections.
This write-up will certainly aid you mount a brand-new tub in your shower room if you have already purchased a brand-new bathtub and do not require to alter the setup of your previous water pipes.
Your devices as well as product list need to comprise the following:
Planning for the Setup
First of all, the supporting frame supplied with the bath needs to be fitted (if required) according to the supplier's guidelines. Next off, fit the taps or mixer to the tub. When suitable the faucet block, it is essential to see to it that if the tap features a plastic washer, it is fitted between the bath as well as the faucets. On a plastic bathroom, it is likewise practical to fit a sustaining plate under the faucets system to avoid pressure on the tub.
Fit the versatile faucet ports to the bottom of both faucets utilizing 2 nuts as well as olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet through the hole in the bath. Use the nut provided by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. See to it you use all of the supplied washers.
Link the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bath should currently be ready to be suited its last position.
Removing Old Touches
If you need to replace old faucets with new ones as a part of your setup, then the first thing you must do is separate the supply of water. After doing so, turn on the faucets to drain any water staying in the system. The process of getting rid of the existing taps can be fairly troublesome due to the restricted accessibility that is commonly the case.
Make use of a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipes to the faucets. Have a cloth prepared for the continuing to be water that will come from the pipes. When the supply pipelines have actually been removed, utilize the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single taps from transforming during this process. When the taps have actually been removed, the holes in the bath/basin will have to be cleaned up of any old sealing compound.
Prior to proceeding to fit the brand-new taps, contrast the pipe connections on the old faucets to the new faucets. If the old taps are longer than the new faucets, then a shank adapter is required for the brand-new taps to fit.
Setting up the Tub
Using both wood boards under its feet, position the tub in the required setting. The wooden boards are useful in uniformly spreading the weight of the bathtub over the area of the boards rather than focusing all the weight onto four small factors.
The following objective is to guarantee that the bathtub is leveled all round. This can be accomplished by checking the spirit level and also readjusting the feet on the bathtub up until the spirit level reviews level.
To set up taps, fit the bottom of the furthest flexible tap connector to the appropriate supply pipeline by making a compression join; then do the exact same for the various other tap.
Activate the water system and also inspect all joints and also new pipework for leaks and also tighten them if necessary. Fill up the bath tub and likewise examine the overflow electrical outlet as well as the regular outlet for leakages.
Finally, fix the bath paneling as described in the supplier's user's manual. Tiling and also securing around the bathtub should wait till the bathtub has actually been utilized a minimum of when as this will certainly resolve it right into its last position.
Suitable New Taps
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic connector to prevent damage to the string. One end of the connector fits on the plastic tail of the tap as well as the various other end provides a connection to the current supply pipes.
If you require to fit a monobloc, then you will call for minimizing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, position the faucet in the mounting opening in the bath/basin making certain that the washers remain in place in between the faucet as well as the sink. Protect the tap in position with the producer provided backnut. As soon as the faucet is firmly in place, the supply pipes can be connected to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with regular faucet adapters. The former type should be attached to the tap finishes first, tightening only by hand. The supply pipelines can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Bathtub
In the area where the bath meets the floor tile, it is essential to secure the joins with a silicone rubber caulking. This is essential as the installation can relocate sufficient to fracture a stiff seal, causing the water to penetrate the wall surface in between the bathroom and also the tiling, causing issues with dampness as well as possible leaks to the ceiling below.
You can choose from a selection of coloured sealers to blend in your fixtures as well as fittings. They are sold in tubes and also cartridges, and are capable of sealing spaces up to a size of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with twists of drenched paper or soft rope. Keep in mind to always fill up the bathtub with water prior to sealing, to permit the activity experienced when the tub is in usage. The sealer can break relatively early if you do not take into account this activity prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally easily offered on the market. It is a good idea to fit the tiles using water-resistant or waterproof sticky and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I am just very focused on Tools You Need to Install a New Bathtub and I hope you liked my blog entry. Appreciated our article? Please share it. Let others discover it. Thanks for your time. Kindly stop by our blog back soon.
Reliable? That's us!